Volkswagen Polo

Note that you might need to turn the ignition off and back on twice for the customization to take effect.

You may also need to reset your 'Lights' settings to 'Factory defaults' in your infotainment system for this customization to work.

You must activate "acoustic confirmation" in your infotainment system for this customization to work.

You must activate "acoustic confirmation" in your infotainment system for this customization to work.

Which start screen logos are supported is dependent on the module's firmware. Please note that setting a start screen logo which isn't supported may cause a "01543 - incorrectly coded" fault code - returning the original logo should fix the issue.

Enabling this mode can be used for storage/transportation purposes. Note that when the mode is enabled your keyfob and alarm will be deactivated!

To disable the start/stop system, set the voltage value to over 12 volts. You won't get any indication that the system is off.

You won't get any indication that the system is off.

To enable this option, the climate control temperature with remote start must be set to a fixed value.

Note that you might need to turn the ignition off and back on twice for the customization to take effect.

Which start screen logos are supported is dependent on the module's firmware. Please note that setting a start screen logo which isn't supported may cause a "01543 - incorrectly coded" fault code - returning the original logo should fix the issue.

You must also enable Scandinavian DRL: daytime running lights activate taillights and parking lights for this customization to work.

If activating this setting, make sure that Bluetooth availability is set to ON.

To use this retrofit setting, your infotainment unit must support CarPlay and have a retrofitted USB port compatible with CarPlay, along with a CarPlay license.

Please note that this customization requires infotainment reboot.

This customization requires that your car is equipped with a satellite navigation system.

Please note that this customization requires infotainment reboot.

You also need to enable TP and RDS in your radio's menu for this to work. Also keep in mind that you might need to wait an hour or so for the feature it to start receiving messages.

Note that you need to enable all steps for this to work.

Note that you need to enable all steps for this to work.

You may also need to reset your 'Lights' settings to 'Factory defaults' in your infotainment system for this customization to work.

You may also need to reset your 'Lights' settings to 'Factory defaults' in your infotainment system for this customization to work.

Adjust the light brightness percentage from 0 to 100.

If you are activating this setting make sure that the brightness option for it is above 0.

If you are activating this setting make sure that the brightness option for it is above 0.

If you are activating this setting make sure that the brightness option for it is above 0.

If you are activating this setting make sure that the brightness option for it is above 0.

Adjust the light brightness percentage from 0 to 100.

Due to differences in lighting hardware and cabling, this setting may not have any effect on SEAT cars (Leon included).

Due to differences in lighting hardware and cabling, this setting may not have any effect on SEAT cars (Leon included).

With this customization, you can have your inner taillights light up together with the main brake lights. After activation, you may need to set the lights brightness to a non-zero value in the "Lights: Daytime Running Lights (DRL)" category under "Left/Right inner taillight brightness".

With this customization, you can have your inner taillights light up together with the main brake lights. After activation, you may need to set the lights brightness to a non-zero value in the "Lights: Daytime Running Lights (DRL)" category under "Left/Right inner taillight brightness".

You must activate "acoustic confirmation" in your infotainment system for this customization to work.

You must activate "acoustic confirmation" in your infotainment system for this customization to work.

This setting only applies to cars that have a rear view camera installed.

Note that you need to enable all steps for this to work.

Note that you need to enable all steps for this to work.

Note that you need to enable all steps for this to work.

Note that you need to enable all steps for this to work.

Note you may also need to enable opening/closing windows via remote for this to work.

Note you may also need to enable opening/closing windows via remote for this to work.